If you are replacing the barrel in a uPVC or composite door, the length matters just as much as the type of lock. A euro cylinder can be the correct overall length but still have the wrong split between the inside and outside. This guide explains what to measure before ordering a replacement.
What is a euro cylinder?
A euro cylinder is the removable key-operated part of many uPVC, composite and some timber door locks. It is normally held in place by a long fixing screw accessed from the edge of the open door. The cylinder operates the locking mechanism, but it is not the same part as the multipoint gearbox inside the door.
How to measure a euro cylinder
- Keep the door open and secure. Do not attempt to remove a cylinder from a locked door. If the key or mechanism is jammed, arrange an inspection instead of forcing it.
- Find the fixing-screw position. Look at the edge of the open door for the screw that lines up with the cylinder. Its centre is the reference point for the measurements.
- Measure the inside. In millimetres, measure from the centre of that fixing-screw position to the inside end of the cylinder body. Include the depth of the fitted handle or escutcheon when checking the required fit.
- Measure the outside. From the same centre point, measure to the outside end of the cylinder body. Write this measurement down separately.
- Check the overall length. Add the two figures together. For example, a 35 mm inside measurement and 45 mm outside measurement make an 80 mm cylinder, commonly described as 35/45.
- Confirm which side is which. Suppliers do not always present the two numbers in the same order. Check their size diagram and clearly label your inside and outside measurements.
If you are confident removing the old cylinder while the door is open, measuring the loose cylinder from the centre of its fixing-screw hole to each end can be more accurate. Keep the screw and cylinder safe, and do not leave the property unsecured. You do not need to remove it if you can measure the fitted lock reliably.
Why the two measurements matter
Two cylinders can both measure 80 mm overall but have different splits, such as 40/40 and 35/45. The lock case may sit off-centre in the door, so simply dividing the total length in half can lead to the wrong replacement. Measure both sides independently.
Check the external projection
Look at how far the current cylinder extends beyond the outside handle or protective escutcheon. A cylinder that sticks out unnecessarily can be easier to grip and attack. Aim for a close fit and check the fitting instructions for the particular cylinder and door furniture. Do not choose a longer barrel just because the overall length sounds familiar.
Double cylinder or thumbturn?
A double cylinder uses a key on both sides. A thumbturn cylinder has a key on one side and a turn on the other. If you need a thumbturn, record which side faces indoors; measure the cylinder body rather than including the projecting thumbturn knob. Make sure the replacement suits your door and your household’s exit arrangements.
What about anti-snap security?
Correct sizing helps, but it is not a substitute for suitable security hardware. For an external door, consider an appropriately certified anti-snap cylinder and compatible protective furniture. You can read more about our anti-snap lock installation service and lock changes in Dundee.
When to ask a locksmith
If the key turns stiffly, the handle needs excessive force, or the door only locks when lifted or pushed, the problem may involve door alignment or the multipoint mechanism rather than the cylinder alone. Fitting a new barrel will not necessarily solve that. Our uPVC door repair service covers these faults.
Common questions
Can I order using the total length alone?
No. Record the inside and outside lengths separately. An 80 mm cylinder is not automatically a 40/40 cylinder.
Where do I start measuring?
Use the centre of the fixing-screw hole, not the end of the keyhole or an estimated halfway point.
What if my measurements are between standard sizes?
Recheck the measurement and the manufacturer’s diagram. The best fit depends on the door furniture and how much of the cylinder would be exposed. Ask for advice rather than guessing.
For help identifying or fitting the right lock in Dundee and nearby areas, contact Locksmith Dundee Ltd on 01382 671054. We can check the existing cylinder and whether the door needs adjustment before recommending a replacement.
Technical reference: ERA 3 Star Euro Cylinder fitting and measurement instructions.